Alloy 20 Tube to Female Pipes Manufacturer

Sachiya Steel International Is One Of The Leading Manufacturer And Exporter Of High Quality Alloy 20 Tube to Female Pipes, The standard operating range for alloy 20 tube fittings is temperatures under 600 degrees Fahrenheit. Alloy 20 Compression Fittings are susceptible to graphitization at higher temperatures, which can seriously impair their performance. When shaping Alloy 20 Female Connector Fittings, any hot working or cold working techniques may be used.

Alloy 20 Tube to Female Pipes Manufacturer In India | Alloy 20 Tube to Female Pipes Manufacturer In Mumbai | Alloy 20 Tube to Female Pipes Exporter In India | Alloy 20 Tube to Female Pipes Exporter In Mumbai | Alloy 20 Tube to Female Pipes Supplier In India | Alloy 20 Tube to Female Pipes Supplier | Alloy 20 Tube to Female Pipes | Alloy 20 Tube to Female Pipes | Alloy 20 Tube to Female Pipes | Alloy 20 Tube to Female Pipes | Alloy 20 Tube to Female Pipes

 

Alloy 20 Tube to Female Pipes
Alloy 20 Tube to Female Pipes

For Alloy 20 Ferrule Fittings, hot working temperatures should range from 1200 degrees Fahrenheit to 2250 degrees Fahrenheit, with heavy forming taking place at temperatures above 1600 degrees Fahrenheit. The recommended temperature range for annealing alloy 20 double ferrule fittings is between 1300 and 1600 degrees Fahrenheit. Carpenter 20 Compression Tube Fittings’ mechanical characteristics and structural make-up can be significantly influenced by the annealing temperature and time at a temperature that is chosen. Carbon content in Carpenter 20 Female Connector Fittings becomes crucial when operating temperatures are anticipated to exceed 600 degrees Fahrenheit.

Carpenter 20 Tube Fittings are less prone to embrittlement because of their lower carbon concentration, which also makes them resistant to graphitization. Carpenter 20 Ferrule Fittings are highly resistant to various corrosive conditions and have strong mechanical qualities. It is possible to weld Female Pipes to Alloy 20 Tube using customary techniques. It is very beneficial to post-heat and pre-heat Alloy 20 Tube to Female Pipes to 300 Degree F to 600 Degree F. A few of the wonderful characteristics of alloy 20 tubes to female pipes are its resistance to oxidation up to 2000 degrees Fahrenheit, to molten copper, to excellent thermal conductivity, to low strength, to suffixation, and more. Meanwhile, common uses for these Alloy 20 Tube to Female Pipes include heat treating, salt baths, boiler tubes, pre-heaters, molten lead, cement kilns, waste heat boilers, and heat exchangers.

Alloy 20 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
: 3000 – 4000 PSI
Applicable Temperature
: 150-400 C
Type
: Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.
Alloy 20 Tube to Female Pipes Fitting Chemical Composition

 

Alloy 20 Ni C Mo Mn Si Fe Cu S P Cr
32 – 38 0.02 max 2 – 3 1 – 2 0.7 max Bal 3 – 4 0.005 max 0.02 max 19 – 21
Alloy 20 Tube to Female Pipes Fitting Mechanical Properties

 

Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
8.1 g/cm3 1443 °C (2430 °F) Psi – 35000 , MPa – 241 Psi – 80000 , MPa – 551 30 %
Equivalent Grades for 20 Alloy Tube to Female Pipes Fitting

 

STANDARD UNS WERKSTOFF NR. AFNOR EN JIS BS GOST
Alloy 20 N08020 2.4660 Z2NCUD31-20AZ NiCr20CuMo
Alloy 20 Tube to Female Pipes Application Industries

 

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
Alloy 20 Tube to Female Pipes Test Certificates

 

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

 

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

 

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Alloy 20 Tube to Female Pipes

Sachiya Steel International Is One Of The Leading Manufacturer And Exporter Of High Quality Alloy 20 Tube to Female Pipes, The standard operating range for alloy 20 tube fittings is temperatures under 600 degrees Fahrenheit. Alloy 20 Compression Fittings are susceptible to graphitization at higher temperatures, which can seriously impair their performance. When shaping Alloy 20 Female Connector Fittings, any hot working or cold working techniques may be used.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5

Leave a Comment

Your email address will not be published. Required fields are marked *